ESD Simulator ONYX 30

Spec：ONYX30(订货号2499982)

Standard：GB/T17626.2 / ISO 10605

Introduction：The Haefely-Hipotronics ONYX 30 ESD gun is the replacement for the PESD 3010. This electrostatic discharge simulator is available in 16kV or 30kV models. The ONYX 30 is the 30kV version.

ONYX Electro Static Discharge Simulator.

Features

16kV and 30kV versions

All in one design (no base unit)

Battery operation, long battery life

Touch screen interface

Ergonomic design

Smart key operation

Modular (R/C modules for ISO, MIL etc.)

Automatic polarity switching

Remote control & automated report generation

Multilingual menus

Temperature and humidity monitoring

One solution for: IEC/EN 61000-4-2 edition 2 (2009), ISO 10605, and many others

Benefits

All in one design
Ergonomic design and operation
Fully compliant ESD Tester
Battery operated

accessories

Coupling Planes (HCP, VCP, GRP)
Indirect injection of ESD fields into the EUT can be accomplished using Horizontal and Vertical Coupling Planes. The Vertical Coupling Plane is effectively an antenna of dimensions 0.5m x 0.5m which is placed on the Horizontal Coupling Plane but isolated from it.

An ESD generator is then placed in the center of the vertical edge and at least 10 impulses of either polarity are applied. In cases where the EUT is large and cannot be placed on the test table, the Vertical Coupling Plane should be held parallel to and 0.1m from the EUT surface.

The Coupling Planes require the use of a special cable with 2 x 470kOhm resistors at either end. This is for connection to the Ground Reference Plane which should be connected to the protective earth system.

Vertical Coupling Plane VCP

Horizontal Coupling Plane HCP

EMC Standard Test Table
The all wood table construction ( 0.8x0.8x1.6m) is necessary becausethe ESD phenomena is basically a radiation. Metal objects in the tableconstruction would therefore distort the field.

Included with the test table is a Horizontal Coupling Plane which completely covers the table upper surface. This defines the maximum EUT size as being 0.6m x 1.4m.

EMC Test Table (metal free)

ESD Calibration Set 2GHz & 4GHz
In order to comply with the calibration requirements of the IEC/EN 61000-4-2 standard, measurement of individual impulse paremeters have to be performed using a special coaxial current target. Since ESD events can be generated up to 120A, attenuators are required to reduce the impulse level so it can be displayed on commercial oscilloscopes.

We offer ESD gun users a complete calibration setup which includes the necessary coaxial current target, attenuators, coaxial cable, user manual and test certificate.

In addition, the brand new ESD 4GHz Calibration Set version is also available for users who wish to perform verification according to the 4GHz requirements of IEC/EN 61000-4-2 Edition 2.0.

PREVIOUS：ESD test Accessories NEXT：100A Three-Phase Coupling/Decoupling Net

Coupling Planes (HCP, VCP, GRP) Indirect injection of ESD fields into the EUT can be accomplished using Horizontal and Vertical Coupling Planes. The Vertical Coupling Plane is effectively an antenna of dimensions 0.5m x 0.5m which is placed on the Horizontal Coupling Plane but isolated from it. An ESD generator is then placed in the center of the vertical edge and at least 10 impulses of either polarity are applied. In cases where the EUT is large and cannot be placed on the test table, the Vertical Coupling Plane should be held parallel to and 0.1m from the EUT surface. The Coupling Planes require the use of a special cable with 2 x 470kOhm resistors at either end. This is for connection to the Ground Reference Plane which should be connected to the protective earth system.	Vertical Coupling Plane VCP Horizontal Coupling Plane HCP

EMC Standard Test Table The all wood table construction ( 0.8x0.8x1.6m) is necessary becausethe ESD phenomena is basically a radiation. Metal objects in the tableconstruction would therefore distort the field. Included with the test table is a Horizontal Coupling Plane which completely covers the table upper surface. This defines the maximum EUT size as being 0.6m x 1.4m.	EMC Test Table (metal free)

ESD Calibration Set 2GHz & 4GHz In order to comply with the calibration requirements of the IEC/EN 61000-4-2 standard, measurement of individual impulse paremeters have to be performed using a special coaxial current target. Since ESD events can be generated up to 120A, attenuators are required to reduce the impulse level so it can be displayed on commercial oscilloscopes. We offer ESD gun users a complete calibration setup which includes the necessary coaxial current target, attenuators, coaxial cable, user manual and test certificate. In addition, the brand new ESD 4GHz Calibration Set version is also available for users who wish to perform verification according to the 4GHz requirements of IEC/EN 61000-4-2 Edition 2.0.